|
|
Thread: genuine racing beat dellorto 48 dhla intake system, many new parts
|
Brad
Rotorhead
Posts: 1672
|
posted January 07, 2008 10:24 PM |
 Edited By: Brad on 7 Jan 2008 23:14 |
Genuine Racing Beat Dellorto 48 DHLA intake system, MANY NEW PARTS
This intake has been my pride and joy for the last 4.5 years and now it's time to let it go. Very well maintained, rebuilt twice since I've owned it! Cleaned on a regular basis. I've run a lot of Seafoam, Amsoil PI, Gumout Fuel Injection Cleaner in the gas tank since I've owned this carb so you know it's clean internally. Tuned with wideband O2 sensor, this puppy runs sweet. Fantastic low to midrange and the top end does not dissapoint.
Many upgrades and new parts. You won't find a nicer Dellorto anywhere! This carb will last a very long time.
All cleaned up and ready to install. Look how shiny all that aluminum is!!!
Manifold is for the Old School 13b 4-port.
Rebuilt recently, all new gaskets, o rings, and Accelerator pump diaphragm
New thick accelerator pump gasket, just like Racing Beat. NLA!!!
New carb Lid. aka Top Cover. Not cheap. The choke operated a lot better after the new lid was installed, and overall the carb just ran smoother!!!
New floats
New, proper sized 3.00mm needle and seat. These are no longer available anywhere!
New plastic jet cover and gasket
New anti-vibration soft mounts and nylox nuts
New idle mixture screws, washers, o-rings, and springs
New progression hole threaded plugs
New accelerator pump rod assembly
New screws for carb Lid.
4" long TWM Induction bellmouth velocity stacks. State of the art. Flow more air than any other stack. Really helps low and mid range torque
New nylox nuts and washers for stacks.
6" long K&N air filter, great shape low mileage
Authentic Racing Beat air filter plates
39mm chokes installed, and 40mm chokes included
Many Spare jets.
Authentic Racing Beat two piece intake manifold
New bolts to attach the 2 piece manifold
Gasket inbetween 2 piece manifold replaced in 2004
The air filter is very long to fit the stacks, and allow the most air to flow in. And requires you either bend or cut/reweld the oil filler tube or just plug it with the included red plastic plug.
.
.
.
.
.
.
$699.00 + shipping Local Los Angeles pickup can be arranged. Ready to sell. Serious buyers only. Lowballers don't waste my time or yours. It would cost you > $1100 to piece this together and still many parts are No longer available (all RB specific parts and 3.00 n/s) !!!!
Contact me by clicking the envelope button below to send direct email. I also pop up on this website a few times a day and have IM enabled.
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
mazdarx605
Redlining
Posts: 314
|
|
posted January 08, 2008 05:50 AM |
|
Hey Brad,
Sweet setup you have there. I was wondering if this will fit any 4-port 13B,or only the old school like you mentioned? I ask becasue my truck has a cobbled together(I think) 4 port 13B. I think one of my rotor housings is from a GSL-SE engine,and the other is of unknown origin. Neither of the housings have the old school MAZDA script. I know it is a 4-port,but I am not sure what type of intake is on it aside from that fact that it looks like a stock unit with the air control valve area all welded up. If this will fit my truck I am interested,even though my wife may not like the idea of spending this type of money. I will try to get a picture of my engine,so you could try to answer my questions.
Chris
74 green REPU
79 spark yellow RX-7 GS
|
|
tom93r1
Redlining
Posts: 458
|
|
posted January 08, 2008 08:42 AM |
|
The intake port sizes are different between the old school 4 ports and the newer 4 ports like from a turboII motor.
Thats the boat I am in right now, I need something to work on the turboII motor I have ported out and will be dropping in my REPU. This should work, but for best results some fairly big port matching will be needed.
____________
'74 lawn-green
4-port 13b
Weber 48DCO
Racing Beat Header
Magnaflow
resonator/amplifier
really loud!
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted January 08, 2008 11:17 AM |
|
It will bolt up to a 4 port 13b that is not using turbo irons. So if your 4 port motor was made using 12a front, intermediate, and rear plates it'll bolt up and line up. That is a very popular setup.
Since you have at least one GSL-SE rotorhousing, which uses water seals in the rotorhousings, and all turbo blocks have the water seals in the irons, it's safe to say you have a pre-2nd gen rx7 motor and not turbo.
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
Klaus44
Redlining
Posts: 365
|
posted January 08, 2008 11:59 AM |
|
Man, that's sweet!
Sure wish I had better cash flow this time of year...
Only thing I'm curious about, after seeing the pic's: what about unfiltered air making it past those zip ties on the cover?
On the off chance someone buys something from me before you sell, you'll hear from me!
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted January 08, 2008 01:35 PM |
|
|
I use grey RTV Silicone. Copper works too.
|
|
repumax
Redlining
Posts: 427
|
|
posted January 08, 2008 07:56 PM |
|
Well! Lets hear it . How is the weber working out for you?Drive her down and lets do a Stone brewing part 2.
____________
1974 Mazda Repu
1986 Yamaha RZ 500
1988 Yamaha YSR 50
1991 Suzuki RGV 250
1992 Yamaha TZR 250 SP
1996 Aprilia RS 250
2003 Ford F-450 6.0 Diesel
2004 Mazda RX8
2006 Yamaha Banshee
2014 18' Eclipse Toy Hauler
|
|
Brad
Rotorhead
Posts: 1672
|
posted January 14, 2008 11:16 AM |
|
Still for sale
Who is interested?
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted January 21, 2008 01:18 PM |
|
Last chance for REPU owners
Any REPUheads intereseted let me know a s a p.
An rx7 owner wants this.
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
Klaus44
Redlining
Posts: 365
|
|
posted January 22, 2008 10:47 AM |
|
Anyone who has the $$$...
...would be foolish to pass up on this. I wish it were me; regret that I cannot afford it, right now...
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted January 22, 2008 04:21 PM |
|
yeah, also put it up on craigslist
the rx7 owner wants free shipping and that ain't gonna happen.
____________
-brad-
74 REPU Lawn Green
81 Rx-7 racecar. 12a J-
Bridge
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted February 11, 2008 09:00 AM |
|
ok people
buyer backed out so
this is still for sale
|
|
jfaplanet
Redlining
Posts: 356
|
|
posted February 11, 2008 02:40 PM |
|
Brad, $699 still your price? Whats shipping to zip 37167? Thanks, Charles
____________
74 REPU "Red"
74 REPU "Jethro" "TII"
74 RE-Courier vert
79 SA-SE(aka deathtrap)
79 SA-SE-FC (project
turbo)
http://home.bellsouth.net
/p/PWP-crgj
TN Forum:
http://tnrotary.10.forume
r.com/
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted February 11, 2008 03:11 PM |
|
Yes, do you want it insured for the full $699? It gets pricey.
FedEx Ground has the best rate for trackable shipments and is who I usually ship with.
|
|
jfaplanet
Redlining
Posts: 356
|
|
posted March 05, 2008 04:35 PM |
|
|
anders
Newbie
Posts: 5
|
|
posted April 11, 2008 04:19 PM |
|
|
Brad
Rotorhead
Posts: 1672
|
|
posted April 11, 2008 06:14 PM |
|
Sold sold sold
Sold sold sold
|
|
|
|
